Research on Compressed Air Ejection Interior Ballistics Based on AUTODYN

Research on Compressed Air Ejection Interior Ballistics Based on AUTODYN

The ultra-short-range defensive weapon system is a kind of attacking ammunition weapon system used for striking the last sensitive and submunitions within the range of 20~200m from the protected target. The compressed air ejection method adopted avoids the gas jet impact problem caused by the ammunition propellant combustion when the self-propelled emission mode is used, which does not generate large infrared characteristics, and improves the initial velocity and payload of the ammunition, and also satisfies the super near The defensive requirements of the infrared defense feature are small and the response speed is fast.

1990-), male, Shandong Weihai, graduate student, research direction is compressed air ejection.

The compressed air ejection system was first applied to the launch of torpedoes. After World War II, with the development of ballistic missiles and over-the-horizon air-to-air missiles, it was gradually applied to the launch of strategic missiles and medium-range air-to-air missiles. Currently, people are using compressed air ejection systems. Ballistic research has achieved a lot of research results. Qiao Wei proposed the estimation method of torpedo motion parameters in the torpedo launcher tube using compressed air emission. 3 Xu Bin used the joint simulation of SIMULINK and ADAMS to study the ejection force of airborne missile. Learning behavior 4, Liao Zhenqiang established a mathematical simulation model of the ejection device under high-pressure nitrogen driving, and analyzed the separation parameters and separation posture of the missile. 5. Based on the previous research, this paper uses compressed air emission for the ultra-short-range defense system. The device is applied in the background, at the muzzle initial velocity Cong Longteng, etc.: Based on the AUTODYN-based compressed air ejection internal ballistics research requirement of 120m/s, the internal ballistic model of the compressed air launching device is established by using the AUTODYN software, and the compression is performed according to the numerical simulation of the model. Air pressure, partial structural parameters of the launcher and projectile ejection

1 The structure of the launching device and the internal ballistic model are shown. The device uses an electromagnet lock mechanism to control the launch. The principle is that the ammunition is pressed against the membrane diaphragm at the discharge port of the compressed gas cylinder under the action of the lock body to control the high voltage. gas. At the time of launch, the electromagnet is energized, the armature moves to the left, the handle and the latch body lose the armature restraint and move upwards. At this time, the lock body cannot continue to restrain the ammunition, the compressed air breaks through the diaphragm, enters the inner ballistic portion of the launch tube, and pushes the ammunition movement. .

Taking into account the need for maintenance and re-use, the design of the program is designed as follows: the rear part of the launch tube is the space for storing compressed air. When normal, the compressed air is not stored. When entering the combat readiness state, first attach it to the discharge port. The membrane is then filled with ammunition so that the ammunition is placed against the membrane membrane, the handle is pressed to close the ampoule to the ammunition, the electromagnet armature is pressed against the handle, the locking force begins to act, and the ammunition is restrained. At this point, the compressed air storage area at the rear of the launch tube is started to be inflated. After the inflation is completed, the system enters the standby state.

1.1 Determination of the relevant parameters of the ballistic model in the launching device On the basis of the above device, the known ammunition quality: 4kg; muzzle initial velocity: 120m/s; energy utilization coefficient n: 0.15; constant volume specific heat capacity: 717JkgK); after the throttle valve is throttled Air temperature: 266K. The compressed air mass required to launch the ammunition is calculated as follows: Calculated: mB0 If the initial pressure of the cylinder is selected to be 35 MPa and the compressed air cylinder temperature is 300 K, then the volume of the compressed air cylinder is: And the air gas constant, and = 287Jkg-K). Calculated: VB0 assumes that the high-pressure gas cylinder is a cylindrical tank, the diameter of the tank diameter D is compressed, and the approximate size range is determined. This data can be used as the initial data for the ballistic estimation in AUTODYN. H. 1.2 Analysis of the impact of internal ballistic performance In order to verify the effect of high pressure air pressure on the performance of the internal ballistics, model 1 was established in the AUTODYN software to verify the effect of high pressure air at different pressures on the internal ballistic performance of the muzzle initial velocity. 7. In order to verify the discharge area of ​​the high pressure gas cylinder Ballistic performance impact, model 2 was established in the AUTODYN software to verify the effect of high pressure air on the internal ballistic performance of the muzzle initial velocity under different discharge areas.

The characteristics of Model 1 are many considerations, except that the compression of the air filled in the model should be considered. In actual cases, the high-pressure air is compressed by the emission cylinder through the channel with smaller diameter and flows into the ballistic portion of the launch tube, and the launch tube is also considered. Friction with ammunition. Model 2 mainly considers leakage, which is relatively simple.

In the model simplification, the ammunition model is simplified to a cylindrical shape for ease of calculation, and the simplified state of the ammunition is as shown.

The difference is that in the high-pressure air region of the model 1, the high-pressure air of 34 MPa, 35 MPa, and 36 MPa is filled on the basis of the discharge diameter of 20 mm. On the basis of the high pressure air of 35 MPa, the model 2 has a discharge diameter of 20 mm, 24 mm and 28 mm respectively. In the case of the elastic tube clearance, due to the different launching systems of the compressed air launching device and the artillery and rocket launcher, there is no The radial elastic deformation of the rocket caused by the high temperature of the rocket engine combustion chamber, the temperature difference between the barrel and the ammunition, and the carbon deposit during the continuous shooting process. Therefore, the factor that can significantly affect the elastic tube clearance of the compressed air launching device is the ammunition geometry. Shape error. Ammunition geometry error is mainly subject to the concentricity of the connecting threads of the various components constituting the ammunition and the axis bending of the various components of the ammunition. 8. In the various components of the ammunition, the warhead often has a large wall thickness, a large rigidity, and is not easy to generate geometry. Bending, while the ultra-short-range defensive weapon system uses compressed air launching. There is no rocket engine or other thin-walled structure on the ammunition. Therefore, the ammunition used in the ultra-short-range defensive weapon system tends to be stiff, and the elastic tube clearance can be set. Significantly smaller than the bullet clearance of rockets and other weapons. By comparing the elastic tube clearance of the relevant weapon, the friction coefficient of the ammunition model and the upper and lower launch tube models is set to /=0.15 in the setting of the model-Lagrange combination to simulate the emission from the ammunition in the launch tube. The friction of the wall of the pipe.

Lagrange-Lagrange requires that the minimum distance between two parts should not be less than 1/10 of the minimum mesh size. In this model, the elastic tube gap is 0.1mm and the single side distance is 0.05mm, so the mesh must be split. The minimum grid size is set to less than.

- In the setting of the Lagrange type, the Euler-Lagrange is set to fully automatic.

2 Numerical simulation results and analysis 2.1 Simulation results of model 1 For the effects of high pressure air with different pressures on the internal ballistic performance of the muzzle initial velocity, the velocity-time and velocity-displacement curves of model 1 are obtained as shown.

Cong Longteng et al.: AUTODYN-based compressed air ejection internal ballistics study selects the displacement-velocity curve of the model. Under the condition of a discharge diameter of 28 mm and a compressed air pressure of 35 MPa, the ammunition can reach a speed of 120 m/s at a displacement of 800 mm.

3 Test comparison According to the simulation data, the experimental model was established. Since 35MPa gas is difficult to obtain, this test uses 20MPa test gas as a comparison, only for software simulation and experimental comparison.

Through the test and test, the time-acceleration data map is obtained, and then the same model simulation is made in the software, and the results of the test data and the software simulation on the same size data are compared.

By comparison, it is found that the software simulation data is too large, and there is a certain error with the test, but the overall trend is maintained, and the error is within the acceptable range. Therefore, the software has a certain credibility, and the process is unstable, and the muzzle initial velocity cannot be obtained. Satisfying the requirement of 120m/s, when the discharge diameter is increased from 20mm to 24mm, the acceleration process becomes obviously stable, the muzzle initial velocity is increased from less than 100m/s to 119m/s, and when the discharge diameter is increased from 24mm to 28mm, The initial velocity of the muzzle increases from 119m/s to 121m/s. 2.3 Speed-displacement relationship extracted from the simulation results Based on the analysis of the above results, in order to obtain the appropriate barrel length, the displacement-velocity curve of the appropriate model is selected as shown.

Discharge flow diameter 20mm flow diameter 24mm discharge diameter 28mm preliminary design stage is acceptable.

4 Conclusions By establishing the internal ballistic model of the compressed air launcher in the AUTODYN software, the relationship between compressed air pressure, launch tube discharge diameter, ammunition displacement, and muzzle initial velocity is obtained. The following conclusions are obtained: 35MPa pressure compression The air acceleration process is not stable. Increasing the discharge diameter of the compressed air can solve the problem that the acceleration process of the ammunition is not stable. (2) The compressed air pressure is 35 MPa. When the discharge diameter is increased from 20 mm to 24 mm, the acceleration process becomes obviously stable. The initial velocity of the mouth increased from less than 100m/s to 119m/s, and the initial velocity of the muzzle increased sharply when the diameter of the discharge was changed from 20mm to 24mm. When the diameter of the discharge increases from 24mm to 28mm, the initial velocity of the muzzle increases from 119m/s to 121m/s, and the lifting is not high; (3) in the case of a discharge diameter of 28mm and a compressed air pressure of 35MPa, the ammunition is displaced at 400mm. The speed can reach 100m / s, the compressed air discharge diameter of the launching device can be set to 35MPa for compressed air pressure, and the length of the launch tube can be set to 800mm.

ChemSta has been dedicated in designing and manufacturing devices used in oil production lines and vegetable protein production lines for more than 30 years. Up to now, there are about 200 successful engineering cases at home and abroad. We have hired over 100 professional engineers in various fields such as machinery, food, electricity and architecture. Hence, we are able to provide appropriate system solutions to meet customer`s requirements.

Harmless Disposal Of Dead Livestock And Poultry Production Line

Harmless Disposal Of Poultry Production Line,Poultry Harmless Treatment Machine,Slaughter Waste Harmless Treatment Machine,Dead Pig disposal Machine

Shandong ChemSta Machinery Manufacturing Co.,Ltd. , https://www.oil-proteinmachine.com