When the fluid flows through the Verabar flowmeter probe, a high pressure distribution zone is created at the front of it, and the pressure in the high pressure distribution zone is slightly higher than the static pressure of the pipeline. According to the principle of Bernoulli's equation, the velocity of the fluid flowing through the probe is accelerated, and a low pressure distribution area is generated at the rear of the probe. The pressure in the low pressure distribution area is slightly lower than the static pressure of the pipeline. After the fluid flows from the Verabar flow meter probe, a partial vacuum is generated at the rear of the probe, and vortices appear on both sides of the probe. The Veloba flowmeter average flow rate probe can accurately detect the average differential pressure generated by the average velocity of the fluid. . Veliba flowmeters follow Bernoulli's equations just like other differential pressure flowmeters qV=KCΔp (1) Where qV———the volume flow of the fluid; K———flow coefficient; C———Flow constant (constant); Δp—The differential pressure produced by the differential pressure generator. C is a constant. To determine qV, K and Δp must be determined. Based on aerodynamics, fluid mechanics theory, boundary layer theory, and actual fluid test data, the Verabar flowmeter has been pioneering the establishment of K's mathematical analysis model for flow probes. K=1/[1/(1-CbβV)+C] (2) Where Cb———the boundary layer coefficient; βV—blocking factor. This is a supplement to the specific application of Bernoulli's equation theory. 1) The accuracy of K is as high as +0.5%, as confirmed by the world-renowned independent flow laboratory. 2) K is linear, its change has nothing to do with the change of Reynolds number, guarantee the measurement result can reach +0.5% of the accuracy under the range ratio higher than 10:1. 3) The flow coefficient of Verabar flowmeter is more accurate and easier to know than other flowmeters. The accuracy and stability of the Verabar flowmeter Δp depends on the unique scientific design of the Verabar flowmeter: 1) The shape of the probe is subject to the least traction, so that the separation point of the fluid and the probe is fixed. 2) The Verabar flowmeter adopts a complete metal cavity structure, which avoids leakage between chambers caused by the three-piece structure of other probes, increases the strength of the probe, and ensures its accuracy. 3) The low-pressure hole is taken on the back side of the probe side, before the probe and the fluid separation point, the low pressure hole is prevented from being affected by the eddy current, and the low-pressure hole is prevented from being blocked, so that the low-voltage signal is more stable and the measurement is more accurate. 4) Surface roughening and anti-slurry: Control the interface layer. At various flow speeds, the fluid in the interface layer on the probe surface is a turbulent layer, ensuring that the probe can obtain stable and accurate signals when the fluid is at a low flow rate. 5) The Verabar flowmeter probe is used to take pressure through multiple pressure-receiving holes through the entire section of the fluid in the pipe. The pressure hole spacing is obtained after area integration. The measured signal is a true signal reflecting the average fluid velocity. The CNC ultra-high pressure Water Jet Cutting Machine is the unique cold cutting new technology in the world, and has an unparalleled lead in the field of material cutting. Compared with other processing technologies, such as flame cutting, plasma cutting, laser cutting, EDM cutting, cnc milling, water cutting does not produce harmful gases or liquids and does not generate heat on the surface of the workpiece. Waterjet Cutting is truly versatile, efficient, and cold-cutting. Water cutting directly uses the kinetic energy of the abrasive water jet to cut the metal to achieve the perfect cutting purpose. no chemical change during the cutting process, no influence on the physical and chemical properties of the cutting material, no thermal deformation, narrow slit, high precision, smooth cut surface, clean and pollution-free, and can process traditional processing and Other processing methods can't process or hard to process materials, such as glass, ceramics, composites, reflective materials, chemical fiber, heat sensitive materials. Water Jet Cutting Machine Water Jet Cutting Machine,Car Washer,Waterjet Cutting Machines,Water Jet MachineWaterjet Parts,Waterjet Spare Parts,Water Jet Cutter,Yc Waterjet HARBIN QIAN FAN XI FENG MACHINERY CO.LTD , https://www.waterjetwamit.com
water jet cutting machine advantages showing:
(1) The roughness of when cutting metal is 1.6μm, and the cutting precision is ±0.10m, which can be used for precision forming cutting;
(2) No reflection effect and edge loss in the cutting of non-ferrous metals and stainless steel;
(3) only need one time to cut carbon fiber composite materials, metal composite materials, metal composites with different melting points and non-metals;
(4) Cutting of low melting point and flammable materials, such as paper, leather, rubber, nylon, felt, wood, explosives, etc.;
(5) Cutting under special site and environment, such as underwater, flammable gas environment;
(6) Cut high hardness and insoluble materials, such as stone, glass, ceramics, cemented carbide, diamond, etc.
Chinese water jet cutting machine now is widely used in all over the world, our waterjet cutter has been exported to more than 15 countries yet, and can provide local service in USA, CHILE,AUSTRILIA,VIETNAM, TURKEY,RUSSIA,UK,INDONESIA. we hope our waterjet cutting machine can bring more customers more business and give you perfect cutting suggestion.
On the principle of Verabar flowmeter and the explanation of related formulae