(1) The use temperature is high, and it can be used for a long time at 1300 °C. The non-metallic materials have strong acid and alkali corrosion resistance, and there will be no oxidation of metal anchors at high temperatures, and the phenomenon of refractory spalling caused by welding; (2) The thermal conductivity is similar to that of the refractory material, which reduces the stress caused by the difference in volume change between different materials; (3) The thermal bridge effect is reduced because the ceramic anchors replace the metal anchors, which reduces the overall thermal conductivity, thus saving energy The effect is also significantly enhanced. By actually measuring the temperature of each section of the grate cooler, the average reduction is 10 °C. Ceramic Anchor,Ceramic Ring,Ceramic Cup,Welded Ceramic Ring Puyu kiln technology (jiangsu) CO.,LTD , https://www.anchorpy.com
Come applicare le pellicole solari per vetri? Istruzioni e guida completa
There are numerous benefits to applying solar films on the glass surfaces of buildings. These films help retain coolness during summer and warmth in winter while shielding the glass, which reduces overheating inside the rooms. The immediate energy savings, and consequently lower utility bills, make this an attractive option. Additionally, solar control films offer excellent UV protection, safeguarding both your skin and your furnishings like sofas, floors, and carpets. All this can be achieved without major renovations, exorbitant costs, or replacing existing windows—just by selecting the right solar film and applying it correctly. Fortunately, the process isn’t overly complicated. Let’s walk through a comprehensive guide with clear, step-by-step instructions to apply solar films to glass without making mistakes.
### What You’ll Need to Apply Solar Films
To successfully apply solar films to glass, you’ll need more than just an adequate roll of solar control film—you’ll also require the following tools:
- A soft, clean cloth for cleaning
- A scraper for cleaning purposes
- A hard rubber squeegee
- A spray bottle for water
- A metal ruler
- A metal square
- A cutter or utility knife with a steel blade
- A spatula
- Paper towels
### Conditions for Installation: Requirements
Before starting, ensure that the conditions are ideal. First, the glass surface must be smooth and in good condition, thoroughly cleaned. The temperature should not fall below 10 degrees Celsius, and it’s best to choose a windless day without drafts, as air currents can complicate the installation and introduce dust particles between the glass and the film.
### Preparing the Glass Surface
As mentioned earlier, a spotless glass surface is essential. Clean the glass using a detergent free of residues like lanolin or wax. The cloth used for cleaning shouldn’t shed fibers either. To ensure the glass is perfectly clean, use a scraper after thorough cleaning, paying special attention to corners and edges near window frames. Once cleaned, you’re ready to apply the solar film!
### Step-by-Step Instructions for Applying Solar Films
Let’s break down how to apply solar films to glass step by step:
1. After cleaning the glass, lightly and evenly mist it with water using the spray bottle.
2. Lay the film upside down, keeping the liner facing you. Thanks to the water on the glass, the film will adhere easily.
3. Remove the protective liner.
4. Now, mist the exposed adhesive side generously with water to activate it. The water removes the hydro-soluble coating protecting the adhesive. After about two minutes, the adhesive will be fully active.
5. Flip the film and position it adhesive-side down onto the glass, misting again.
6. Adjust the film’s position, as it will slide smoothly over the wet surface.
7. Begin spatulaing to flatten the film evenly. Adding a bit of soapy water to the spatula can help it glide smoothly.
8. Use a ruler, square, and cutter to trim the film, leaving a 2 mm gap between the film and the window frame’s rubber seal.
9. Continue spatulaing with more pressure to perfect the application.
10. Finally, use the spatula and paper towel to press the edges firmly into place.
With these steps, you’ve completed the installation of solar films on your glass surfaces. Follow this method to protect every window in your building.
### Post-Installation Notes
Keep in mind that the adhesive on the window films takes approximately 15 days to fully set. Avoid cleaning the glass during this period to prevent damaging the applied film. Patience is key to ensuring long-lasting results!
Prev Article
Spring Cleaning